Welcome to the website of Shandong Gangyan Grinding Ball Co.,ltd. !

Phone:+8615163800896 | E-mail:

Ore conveyor belt carrying mineral feed at a mining processing facility

Wet Grinding Corrosion of Steel Grinding Balls: Variables Mine Operators Should Monitor

In wet mineral grinding, steel grinding balls are exposed to repeated mechanical contact and an aqueous chemical environment at the same time. Their material loss is therefore not always explained by abrasion alone. Corrosion can interact with impact and abrasion, changing the total wear response. For plant metallurgists and maintenance teams, the useful question is not simply whether corrosion exists, but which operating variables should be recorded before comparing media performance.

Ore conveyor belt carrying mineral feed at a mining processing facility
Real mine-site footage showing forged grinding balls discharged from a wet SAG mill during wet grinding. This video illustrates the operating environment; it is not a corrosion test or a measurement of wear performance.

1. Why wet grinding can involve corrosion-assisted wear

Inside a wet ball mill, steel media repeatedly contact ore particles, other balls and the liner while moving through process water and slurry. Fresh metal may be exposed as surfaces wear. Electrochemical reactions can occur on the steel surface, and mechanical action may remove corrosion products or disrupt surface films. This interaction is commonly described as corrosion–abrasion or corrosion-assisted wear.

A 2023 review of grinding media in ball mills reports that corrosive wear can be a major contributor in wet grinding, while also noting that its contribution depends on the system and that further plant-specific verification is important. A 2013 review in Minerals Engineering similarly describes media consumption as the result of interacting variables associated with the media, ore and processing conditions. Neither review provides a universal corrosion percentage that can be applied to every mine.

2. Slurry pH: record the operating range, not one isolated reading

pH affects aqueous electrochemistry and the stability of surface films. However, a single pH reading taken at the sampling point or once per shift may not represent the conditions experienced throughout the mill. Record the measurement location, sampling time, calibration status, temperature where available, and the normal operating range. Also note process changes such as lime addition, reagent changes, water-source changes or a change in ore blend.

Do not assume that a higher or lower pH will always reduce steel media consumption. The response depends on the water chemistry, dissolved species, mineral surfaces and the steel’s metallurgical condition. A site trial should compare periods with documented and reasonably stable operating conditions.

3. Water chemistry and dissolved species

Process water is not chemically neutral simply because it looks clear. Conductivity, chloride, sulfate, dissolved oxygen, calcium, magnesium and other dissolved constituents may influence electrochemical behavior. Recycled water can also change as the plant water balance changes. Where corrosion is suspected, a water analysis is more useful than a general description such as fresh water or recycled water.

  • Record conductivity and the principal ions included in the site’s routine water analysis.
  • Identify whether the mill uses fresh, reclaimed, saline or blended water.
  • Record major water-treatment or reagent changes.
  • Use consistent sampling points and laboratory methods when comparing periods.

Not every plant needs an extensive electrochemical program. Begin with parameters already monitored by the metallurgical laboratory, then add tests only when the operating evidence indicates a meaningful question.

4. Ore mineralogy and galvanic interactions

Ore is an active part of the grinding environment. Sulfide minerals and other electrically conductive or electrochemically active phases can affect reactions at the steel–slurry interface. Changes in ore source, blend, oxidation state or mineral exposure may therefore coincide with changes in media consumption. This is one reason a media comparison performed on different ore blends can produce misleading conclusions.

When a wear trend changes, check the mine’s ore blend and mineralogical records alongside the media data. For copper, gold and polymetallic ores, the relevant mineral phases and their proportions differ. Do not infer a corrosion mechanism from the commodity name alone; use mineralogical and process evidence.

5. Mechanical conditions still matter

Corrosion does not replace abrasion or impact. Mill speed, filling level, ball size distribution, liner condition, throughput, slurry density and the presence of oversized or tramp material can change mechanical contact. A change in ball breakage, surface damage or media size distribution can also affect the apparent consumption rate.

Separate the observations where possible: mass loss, dimensional wear, breakage, spalling and handling damage are not interchangeable measures. If balls are disappearing from the circuit, confirm whether the cause is wear, discharge, screening losses, breakage or an accounting issue before attributing the result to corrosion.

6. Build a defensible plant comparison

For a supplier comparison or a change in media grade, establish a baseline and a written trial protocol. Record the media grade and batch, nominal diameter, delivery date, charging mass, make-up schedule and any changes in ball size distribution. At the same time, record throughput, operating hours, ore blend, slurry density, pH, water source and relevant reagent changes.

Use a defined calculation for consumption, such as kilograms of media added per tonne of dry ore processed, and state the accounting boundaries. Reconcile opening and closing stock, additions, removed balls and any known losses. Compare equivalent periods and avoid drawing conclusions from short intervals with unstable production.

Where practical, run the comparison with one major variable changed at a time. If the ore blend or water chemistry changes materially during the trial, document the change and treat the result cautiously. A laboratory corrosion test can help investigate a mechanism, but it does not reproduce the complete mill environment and should not be presented as a guaranteed plant wear rate.

7. What to ask a grinding media supplier

Ask the supplier to identify the steel grade, heat or batch traceability, heat-treatment route and the inspection records available for the supplied lot. For a wet-grinding investigation, share the mill type, ball diameter, ore type, water source, typical pH range, slurry density and the way consumption is calculated. This information helps the supplier discuss material suitability without claiming that one grade will solve every corrosion problem.

Shandong Gangyan supplies forged grinding balls for mining applications. Product selection should be based on the actual mill duty, requested diameter and agreed material specification. See our grinding ball specifications and contact the technical sales team to discuss a project.

Frequently asked questions

Does corrosion occur in every wet ball mill?

Electrochemical reactions can occur in aqueous slurry, but their contribution to total media loss varies with water chemistry, ore mineralogy, media condition and operating practice. Measure the plant rather than assume a fixed contribution.

Can pH alone predict grinding ball corrosion?

No. pH is one important variable, but conductivity, dissolved species, mineralogy, oxygen availability and mechanical conditions also matter.

Is recycled water always more corrosive than fresh water?

No universal rule applies. Recycled water chemistry varies by site and may change with the water circuit. Compare measured chemistry rather than the water-source label.

Can a laboratory corrosion test predict kg/t consumption?

Not by itself. Laboratory tests isolate selected mechanisms. Plant consumption also includes impact, abrasion, circuit losses and operating variability.

What data should a mine provide for a technical review?

Provide mill type, media diameter and grade, ore blend, water analysis, pH range, slurry density, throughput, operating hours and the method used to calculate media consumption.

References

  1. A Review of the Grinding Media in Ball Mills for Mineral Processing, Minerals, 2023.
  2. Consumption of steel grinding media in mills – A review, Minerals Engineering, 2013.
  3. Google Search Central: Creating helpful, reliable, people-first content.

Technical note: This article explains variables and a method for plant investigation. It does not report a Shandong Gangyan mine trial, promise a fixed reduction in consumption or replace site-specific metallurgical testing.

8. A practical monitoring checklist for the plant team

Use the checklist below as a starting point and adapt the sampling frequency to the site’s process-control plan. The important requirement is consistency: use the same sampling locations, methods, units and reporting periods when comparing operating campaigns. Record changes rather than treating them as noise.

  • Slurry pH: record the value, sampling point, date and time, temperature if available, instrument identification and calibration status. Keep the operating trend, not only a monthly average.
  • Water chemistry: record water source and blend, conductivity, chloride, sulfate and the other ions included in the site’s routine laboratory analysis. Record changes in recycled-water ratio, water treatment or make-up water.
  • Ore conditions: record mine area or ore source, blend proportions where available, sulfide or other relevant mineral phases from the site’s mineralogical records, oxidation/weathering observations and major feed changes.
  • Mill operation: record mill type, operating hours, throughput, slurry density or solids percentage, mill speed, filling or load indicators used by the plant, ball-size distribution, liner condition and reagent additions.
  • Media accounting: record steel grade, nominal diameter, supplier batch, delivery and charging dates, charging mass, additions, removed balls, known circuit losses and the dry-ore tonnage used in the kg/t calculation.
  • Physical observations: keep separate counts or notes for normal wear, dimensional loss, breakage, spalling, unusual surface deposits and handling damage. Photograph representative samples with scale and sample ID.

9. Suggested shift or campaign record

Record fieldWhat to enter
Date, time and sample IDSampling point, operator and laboratory reference
Slurry pH and temperatureMeasured value, instrument and calibration check
Water source and chemistryFresh/recycled/blended; conductivity and available ion results
Ore blend and mineralogyOre source, blend change and available mineralogical notes
Operating conditionsDry throughput, operating hours, slurry density and relevant mill settings
Grinding mediaGrade, nominal diameter, batch ID, additions and removed media
Wear observationsWear, breakage, spalling, deposits and sample/photo reference
Consumption calculationkg added ÷ tonnes of dry ore; state the period and accounting boundary

Do not compare two media grades if the periods have materially different ore blends, water chemistry, throughput or accounting boundaries without identifying those differences. Where possible, establish a baseline, agree the trial period and change one major factor at a time. A plant comparison is stronger when operating data and media batch records can be reconciled.

10. Information to include in a supplier enquiry

For a useful initial review, send the mill type, required nominal diameter and the tonnage needed for each diameter, plus ore type and the available pH and water-analysis records. If several sizes are required, list each size separately rather than giving only a combined tonnage. The supplier can then confirm which material grades and inspection documents are relevant to the requested sizes.

Review the forged steel grinding balls range and our factory and quality-control information, or contact Shandong Gangyan with your diameter and tonnage breakdown.

Technical note: This article provides a plant-monitoring method, not a Shandong Gangyan mine-trial result or a guaranteed reduction in media consumption. No universal pH threshold or corrosion rate is proposed; interpretation must use the site’s water, ore and operating evidence.